The deep-working 425 Disk offers 9 - or 11-inch spacing — perfect for primary tillage in stalks and stubble. And the one-piece welded mainframe is tough enough for rough ground.
Specifications | ||||
---|---|---|---|---|
John Deere 425 Offset Disk |
Type | Rigid |
---|
Spacing option A | 229 mm 9 in. |
|||
---|---|---|---|---|
Option 1 | 2.79 m 9.17 ft, in. |
|||
Option 2 | 3.23 m 10.58 ft, in. |
|||
Option 3 | 3.68 m 12/08 ft, in. |
|||
Option 4 | 4.11 m 13.50 ft, in. |
|||
Option 5 | 4.78 m 15.67 ft, in. |
|||
Spacing option B | 279 mm 11 in. | |||
Option 6 | 2.67 m 8.75 ft, in. |
|||
Option 7 | 3.23 m 10.58 ft, in. | |||
Option 8 | 3.76 m 12.33 ft, in. | |||
Option 9 | 4.01 m 13.17 ft, in. | |||
Option 10 | 4.78 m 15.67 ft, in. |
Spacing option A | 229 mm 9 in. |
---|
mph | 6.4 to 9.7 km/h 4 to 6 mph |
---|
Horsepower required | 41 to 112 kW 55 to 150 hp |
---|
Option 1 | Parallel-lift bar and 5-leaf spring for front-to-rear leveling and increased relative pressure on front or rear gangs |
---|
Option 1 | Mechanical depth stops |
---|
Standard | 1 selective control valve (SCV) required |
---|
Standard | 9-pin connector for warning |
---|
Type | Combination hitch with right or left offset options |
---|
Tubing | Structural steel - 3x5x3/203 mm 8 in. |
---|
Angle | Front 28 to 48 degree (angle) Rear 28 to 48 degree (angle) | |||
---|---|---|---|---|
Tubing | Front Structural steel - 4x6x1/102 mm 4 in. Rear Structural steel - 4x6x1/102 mm 4 in. | |||
Gang bolt | Round - 38 mm 1.5 in. |
|||
Gang standard | Rigid nodular iron | |||
Bearings | Triple-sealed ball bearings with wear guards (no lubrication needed unless grease fittings are installed) | |||
Scraper | Rigid |
Option 1 | Spherical blade with scraper: 356 mm 14 in. | |||
---|---|---|---|---|
Middle breaker | Offset |
Spacing | 229 or 279 mm 9 or 11 in. | |||
---|---|---|---|---|
Size | Option 1 Cutout cone front and solid cone rear or Cutout spherical front and solid spherical rear - 610 x 4.5 mm 24 x 0.177 in. Option 2 Solid cone or Cutout cone front and solid cone rear - 610 x 6.5 mm 24 x 0.256 in. Option 3 Cutout cone or cutout cone front and solid cone rear or cutout spherical front and solid spherical rear - 660 x 6.5 mm 26 x 0.256 in. |
Mainframe wheels and tires\ | Option 1 Two 15-8 wheels with 11L-15 10PR tires Option 2 Two 15-8 wheels less tires Option 3 Two 16-6 wheels less tires | |||
---|---|---|---|---|
Wingframe wheels and tires | Option 1 Wheel tread spacing - 198 cm 78 in. |
Product modules and features has been compiled for worldwide circulation with general information, pictures, and descriptions of features not available in all countries. In some countries, products and accessories may require modifications or additions to ensure compliance with local regulations. Contact your local John Deere dealer for details.